Cold-Knife Tube and Strip Cutter, 160 mm Cutting Width WM-602
The WM-602 cuts tube, hose, foil and non-adhesive strip up to 160 mm wide to a set length with a cold knife — from 1 to 99,999 mm, with a specified cutting accuracy of 0.1 mm and a rated speed of up to 150 cuts a minute. Accuracy and output at your chosen length are verified on your material. It is a 34 kg bench machine drawing 1,100 W on 110 or 220 V, with an English LCD for length, speed and count that keeps its settings through a power cut and stops when the material runs out.
Specifications
| Model | WM-602 |
|---|---|
| Cutting length | 1 – 99,999 mm |
| Cutting accuracy | 0.1 mm |
| Max. cutting width | 1 – 160 mm |
| Cutting speed | 150 pcs/min |
| Knife | Cold knife |
| Voltage / frequency | Reference configuration: 110 V / 220 V, 50/60 Hz |
| Rating power | 1,100 W |
| Dimensions | 430 × 380 × 480 mm (L×W×H) |
| Weight | 34 kg |
| Electrical configuration | We configure the machine’s electrical supply for your installation before shipment. Your quote confirms the voltage, phase, frequency, current and the power cord with plug or industrial connection for your site. Common site supplies are 120 V, 60 Hz with grounded Type B outlets in the US and Canada, with 208 V or 240 V also found at industrial sites. The UK and Ireland use 230 V, 50 Hz with Type G. Australia and New Zealand use nominal 230 V, 50 Hz with Type I, and some Australian sites list 240 V. Three-phase installations in the UK, Ireland, Australia and New Zealand commonly use 400 V at 50 Hz, with 415 V at some Australian sites. |
| Lead time | Your quote confirms the machine configuration, included accessories and dispatch date. |
| Warranty and support | One-year machine warranty and free remote video support for the life of the equipment. |
| Wear parts | For wear parts, every quote lists them with unit price and the location they ship from. |
| HS Code | 8451.50 (common reference — final classification confirmed by your customs broker) |
| Certification | CE (certificate provided with shipment) |
Key features
- 160 mm throat takes heat-shrink and PVC tube, hose, foil and flat strip that will not fit an 80 mm tape cutter
- Cold knife, no heater — clean square ends on heat-shrink without a pre-shrunk lip, and no fumes on the bench
- Specified length accuracy of 0.1 mm and rated speed of up to 150 cuts a minute, with the combined result verified at your required cut length; set length, quantity and speed on the English LCD (LEN / SPD / CUT)
- Settings survive a power cut and the machine stops itself when the roll runs out — a counted batch finishes at the count
- 34 kg, 430 × 380 × 480 mm, 1,100 W on 110 or 220 V — we set the voltage for your country and ship the manual in English
What it processes
- Heat-shrink, PVC and silicone tube cut to a set length for harness kits
- Hose, foil and non-adhesive strip up to 160 mm wide
- Shops cutting the same tube with a knife and a stop who now need a counted batch
Suited for: tube, hose and strip 1–160 mm wide, cold cut to a set length in counted batches. For other jobs and machine options: a melt-sealed edge — WM-577. 80 mm Velcro with shaped ends — WM-612. 800 mm sheet — WM-604.
Tell us your supply voltage on the inquiry; we set 110 or 220 V before shipment.
The stated accuracy and maximum speed are separate specification values. We verify their acceptance conditions together on your material and cut length during the sample trial. To get a WM-602 quote, tell us the material and its approximate width or outside diameter. If you know the target cut length, include it so we can check the setup.
Engineering knowledge
Choose and troubleshoot this process
- Cutting 316 Stainless Wire Rope to 6 Inches with WM-9323A U.S. customer sent 1/8-inch 316 stainless wire rope for a 152.4 mm cut trial. See the cut ends and the checks needed for ferrule fit and length.
- Coated Steel Wire Rope Cutting: Check the End and Sleeve FitSpecify coated steel rope cutting by metal diameter, coating, strand containment and actual sleeve fit. Keep cutting acceptance separate from termination strength.
- Can One Cutter Process Bubble Wrap and Paper Rolls?Choose roll-to-sheet cutting for bubble wrap and paper by feed pressure, unwind control, complete separation and collection, rather than textile sealing.
WM-602 — common questions
Is this a hot knife?
No, cold knife. A sealed melt edge on webbing is the WM-577 (hot and cold, 350 °C, 500 W) or the ultrasonic WM-596.
How many pieces before a machine makes sense?
For a thousand pieces of heat-shrink a month, a guillotine with a stop and a low-skill operator is genuinely hard to beat. This machine pays back when the count is tens of thousands, the length must repeat to a tenth of a millimetre, or the tube is too wide or too tough for a hand cutter. Tell us the monthly quantity and we will say which it is.
I only need 80 mm Velcro shapes.
That is the WM-612.
Will it crush or nick a thin-wall tube?
The knife stroke and feed pressure are set for the material, and thin-wall PVC and heat-shrink are its everyday job. Send 2–3 metres of your actual tube and we cut it on video before you order — a photo of another tube is not a run on yours.
Where do blades come from?
The knife is the wear part. Every quote lists it with unit price and the location it ships from.
Related machines in Tube, Tape & Material Cutting
Hot and Cold Webbing Shape Cutting Machine, 45–135°
Model WM-566
Automatic Plastic Tube Cutting Machine for Ø4–30 mm Tube
Model WM-606
Automatic Braided Sleeve Taping and Cutting Machine for OD 8–30 mm Tube
Model WM-177