🌐 English ▾

Parts, Applicators & Consumables

We supply crimping applicators for 30 mm and 40 mm press arrangements, matched spare dies, cutting blades and stripping blades. Send the press interface details, terminal drawing and wire samples so we can confirm the fit and quote the required parts.

Match the applicator to the press

We supply the following applicator configurations with side-feed or end-feed. These labels describe the configuration; they do not guarantee a fit with every press of the same nominal standard.

Configuration we supplyRequired press strokeFeed types
Chinese / Japanese30 mmSide-feed, end-feed
European40 mmSide-feed, end-feed

Our WM-3102T bench press has a 30 mm stroke, with 40 mm available by customization. Our WM-395 strip-and-crimp station uses European style applicators with a 30 mm stroke. Check the exact press and applicator combination before reusing tooling.

Five checks before an applicator quote

CheckInformation to send
Press strokePress model and specified ram travel: 30 mm or 40 mm where applicable. Confirm the actual configuration of an existing machine.
Press shut heightRequired closed height, its reference surfaces and the measurement procedure from the press and applicator documentation.
Mounting and ram connectionBase mounting drawing and dimensions, plus the ram coupling drawing or clear photographs with the key dimensions.
Feed direction and pitchSide-feed or end-feed, terminal-strip pitch and a carrier-strip drawing or sample.
Terminal and wireTerminal drawing or 20–30 cm of actual strip, production wire samples, conductor size, insulation diameter and the required crimp dimensions.

Press shut height and finished crimp height are different. Shut height describes the closed press-to-tooling interface at specified reference surfaces. Crimp height is measured on the formed terminal. A matching stroke or shut height does not by itself prove that the finished connection meets its specification.

Use our applicator parts, shut height and tooling-fit guide for the interface checks, and our terminal crimping machine selection guide to compare processing routes.

Applicator spare parts

The wearing pieces of any side- or end-feed applicator are the crimper (upper die halves for wire and insulation), the anvil below them, the feed pawl that indexes the terminal strip, and the shear blade that separates the crimped terminal from the carrier. All are replaceable without changing the applicator body. Name the piece if you know it — or photograph the applicator with the worn part visible and we identify it for you.

Cutting & stripping blades

Carbide and steel blade sets for the common benchtop and automatic cut & strip platforms: V-blades, flat blades and die-matched sets. Blade patterns are shared across many Chinese machine brands, so we can usually match a machine we did not supply — send the machine model and a photo of the old blade beside a ruler.

How ordering works

  1. You send — for applicators: the five checks above, including press and applicator details, terminal drawing or strip, and production wire. For blades and spares: machine model plus a photo of the part.
  2. We match — applicator or blade is confirmed against your samples, not against a guess.
  3. We prove — before dispatch, your terminal and wire are crimped on the actual applicator and the video comes to you with crimp-height measurements.

Frequently asked questions

What are the parts of a crimping applicator called?

The main wear parts are the crimper (upper die), anvil (lower die), feed pawl, drag, shear blade and ram. We supply each as a separate spare — send your applicator model or a photo to identify the exact part.

How do I know whether I need a 30 mm or a 40 mm stroke applicator?

Read the required ram travel in the exact press and applicator specifications. We supply Chinese/Japanese 30 mm and European 40 mm arrangements, but the standard name alone does not establish fit. Also match shut height, mounting, ram connection, terminal-feed direction and clearance. WM-3102T lists 30 mm with 40 mm available by customization; WM-395 lists 30 mm despite its European-style description. Send the model and interface drawing so we can confirm the configuration.

Can you supply an applicator if I only have the terminal?

Yes. Send the terminal drawing, or 20–30 cm of the actual terminal strip plus the wire it crimps. The applicator is matched to that terminal's pitch and feed direction, and before it ships we crimp your own samples on it and send the video together with crimp-height measurements.

Do your blades fit machines we did not buy from you?

Usually yes for the common Chinese cut-and-strip platforms, which share blade patterns across brands. Send your machine's brand and model plus a photo of the old blade next to a ruler, and we match it — or tell you honestly that we cannot.

What should a parts inquiry include?

For applicators: press and applicator models; stroke, specified shut height, mounting and ram-interface drawing; terminal drawing, feed direction and a strip sample; conductor size and insulation diameter. For blades and spares: machine model, part reference or drawing, and a photo of the worn part beside a ruler. We confirm the matched configuration and sample-trial requirements on the quote.

Cutting and stripping blades with red and metal feed rollers

Get a price in 12 hours

Tell us your wire and volume — a specialist (not a bot) replies with a full quotation.

For WhatsApp, start with + followed by your country code and number.
Add application details (optional)
Photos, PDF drawings or short videos · up to 5 files · 20 MB each · 50 MB total

🔒 Confidential engineering review. Files stay private and are used only to evaluate your application. Our engineering and sales team replies within 12 hours.

👋 Need help choosing a machine? Ask me about specifications, processes and sample trials.
Email
Wiro — Equipment Assistant Equipment guidance · quotation team replies within 12 h