Automatic Plastic Tube Cutting Machine for Ø4–30 mm Tube WM-606
Our WM-606 cuts pneumatic tubing, low-pressure oil tubing, PVC tubing and heat-shrink tubing to length with a 14-wheel drive and belt feeding. The standard processing range is 4–30 mm; 30–50 mm is available as a custom configuration. A servo-driven blade holder, digital roller-height adjustment and a 7-inch color touchscreen support setup changes. The specified output is 4,000 pcs/h at a 100 mm cut length and Ø10 mm tube diameter. No compressed air is required.
Specifications
| Model | WM-606 |
|---|---|
| Function | Cut-to-length processing of pneumatic tubing, low-pressure oil tubing, PVC tubing, heat-shrink tubing and other plastic tubing |
| Processing range | 4–30 mm; 30–50 mm available as a custom configuration |
| Maximum passage diameter | Ø40 mm; passage for a custom configuration confirmed on the quote |
| Display | 7-inch color touchscreen HMI × 1 |
| Cutting length | 1–999999.99 mm |
| Cutting tolerance | Within 0.003 × L (L = cutting length) |
| Production rate | 4,000 pcs/h at 100 mm cutting length and Ø10 mm tube diameter |
| Drive | 14-wheel drive; servo-motor drive optional |
| Feeding method | Belt feeding |
| Blade-holder control | Servo motor and precision-ground screw |
| Blade-holder travel limits | Digitally adjustable upper and lower positions |
| Pressure-roller height | Digital adjustment |
| Power supply | Reference configuration: AC 220 V, 50/60 Hz; AC 110 V, 50/60 Hz optional |
| Air supply | No compressed air required |
| Optional functions | MES connectivity, IoT connectivity, fixed-position inkjet marking, mid-span stripping, external auxiliary-equipment alarms |
| Expansion | Modular interfaces for accessories and peripheral equipment; upgrades and custom configurations available |
| Dimensions | 950 × 670 × 1300 mm (L × W × H) |
| Net weight | 145 kg |
| Motion controller | 1 unit |
| Transmission belts | 8M × 2 |
| Ball screw | Model 160 × 1 |
| Servo drivers | 6 A × 3 |
| Linear guide | EHG15 × 1 |
| Bearings | 35 pieces |
| Listed servo motor | 400 W × 1; motor rating, not total machine input power |
| Electrical configuration | We configure the machine’s electrical supply for your installation before shipment. Your quote confirms the voltage, phase, frequency, current and the power cord with plug or industrial connection for your site. Common site supplies are 120 V, 60 Hz with grounded Type B outlets in the US and Canada, with 208 V or 240 V also found at industrial sites. The UK and Ireland use 230 V, 50 Hz with Type G. Australia and New Zealand use nominal 230 V, 50 Hz with Type I, and some Australian sites list 240 V. Three-phase installations in the UK, Ireland, Australia and New Zealand commonly use 400 V at 50 Hz, with 415 V at some Australian sites. |
| Lead time | Your quote confirms the machine configuration, included accessories and dispatch date. |
| Warranty and support | One-year machine warranty and free remote video support for the life of the equipment. |
| Wear parts | For wear parts, every quote lists them with unit price and the location they ship from. |
| Certification | CE (certificate provided with shipment) |
Key features
- Prepare repeat tube lengths without measuring each piece by hand: set the cut length through the 7-inch color touchscreen, then use automatic belt feeding and cutting.
- Adjust the working clearance for the tube: pressure-roller height and both blade-holder travel limits are set digitally, with a servo motor and precision-ground screw controlling the cutter.
- Protect the tube surface with belt feeding designed to avoid pressure marks and scratches. We check the surface, cut end and measured length on your tube samples.
- Install without a compressed-air connection: the machine requires electrical power but no air supply. Modular interfaces allow accessories and peripheral equipment to be matched to the job.
- Receive a setup ready for your destination: we set the voltage for your country and ship the English interface and manual.
What it processes
- Pneumatic tubing cut to repeat assembly lengths
- Low-pressure plastic oil tubing prepared in production batches
- PVC tubing cut to length, with material and wall thickness checked on samples
- Heat-shrink tubing and other plastic tubing prepared for downstream assembly
Our WM-606 prepares pneumatic tubing, low-pressure oil tubing, PVC tubing and heat-shrink tubing in repeat cut lengths. Belt feeding and a 14-wheel drive move the material through a floor-standing machine, with length settings entered on the 7-inch color touchscreen. The standard processing range is 4–30 mm, with 30–50 mm available as a custom configuration.
The blade holder uses a servo motor and precision-ground screw. Its upper and lower travel limits and the pressure-roller height are digitally adjustable. The listed maximum passage is Ø40 mm; for a custom tube diameter, we confirm the passage and cutting arrangement before the order. The specified output of 4,000 pcs/h applies to 100 mm cut lengths and Ø10 mm tubing.
Modular interfaces support accessories and peripheral equipment. MES and IoT connectivity, fixed-position inkjet marking, mid-span stripping and external auxiliary-equipment alarms can be selected for the job. These are optional functions, not included in every standard machine.
Send your tube material, outside diameter, wall thickness, target lengths and acceptable tolerance. Include the coil dimensions and recurring batch quantity. We test the application and show the result so you can evaluate the finished pieces before committing to the machine. To get a WM-606 quote, tell us the material and its approximate width or outside diameter. If you know the target cut length, include it so we can check the setup.
Engineering knowledge
Choose and troubleshoot this process
- Pneumatic Tube Cutting for Push-In Fittings: Ends, Length and SeatingPrepare pneumatic tubing for push-in fittings by checking square cuts, sealing surfaces, insertion depth and routing length. Specify an automatic-cutting trial.
- Cutting 316 Stainless Wire Rope to 6 Inches with WM-9323A U.S. customer sent 1/8-inch 316 stainless wire rope for a 152.4 mm cut trial. See the cut ends and the checks needed for ferrule fit and length.
- Coated Steel Wire Rope Cutting: Check the End and Sleeve FitSpecify coated steel rope cutting by metal diameter, coating, strand containment and actual sleeve fit. Keep cutting acceptance separate from termination strength.
WM-606 — common questions
Which tube materials and wall thicknesses can we run?
We cut pneumatic tubing, low-pressure oil tubing, PVC tubing, heat-shrink tubing and other plastic tubing. Send the material, outside diameter, wall thickness and a sample. We test the cut end, surface condition and finished length before confirming the setup.
Is 50 mm part of the standard range, and what does the 40 mm passage mean?
The standard processing range is 4–30 mm. The 30–50 mm range is a custom configuration, while the listed maximum passage diameter is Ø40 mm. These are separate specifications: confirm the passage and cutting setup for your required custom diameter before ordering.
What output can we expect?
The specified production rate is 4,000 pcs/h at a cutting length of 100 mm and a tube diameter of 10 mm. This is not a rate for every material or length. We run your tube and required lengths to confirm the output for your job.
Is the machine fully servo driven as standard?
The blade holder uses a servo motor and precision-ground screw. The 14-wheel drive has a servo-motor option; this does not make every drive a standard servo axis. The component list includes one 400 W servo motor, which is a motor rating rather than the total machine input power.
Which functions are optional?
MES connectivity, IoT connectivity, fixed-position inkjet marking, mid-span stripping and external auxiliary-equipment alarms are optional. We confirm the selected functions, interfaces and any custom tube-processing arrangement on the quote.
What does the cutting tolerance mean?
The specification states within 0.003 × L, where L is the cutting length. This corresponds to 0.3 mm at a 100 mm length and 3 mm at 1000 mm. We measure your sample pieces against the tolerance required by your assembly.
How do you verify my shortest and longest finished tube lengths?
We cut the shortest and longest lengths you require during the sample run and check the finished pieces. The published 1–999999.99 mm figure is the programmed setting range. The tube and setup determine the usable lengths.
Will it feed directly from our coil?
We review coil weight, dimensions and the incoming path before confirming the setup. Supply drag can affect feeding even when the tube fits the guides. For a matched coil supply arrangement, see our payoff and feeding equipment.
Is automation worthwhile for an occasional batch of 1,000 pieces?
A suitable hand cutter and length stop may be sufficient for occasional small batches. Automatic cutting becomes more useful when recurring batches of many thousands keep staff measuring and cutting instead of assembling. Send the batch frequency and piece lengths so we can assess the job with you.
What power and air supply does it need?
The power supply is AC 220 V, 50/60 Hz, with AC 110 V, 50/60 Hz available as an option. No compressed air is required. We set the voltage for your country and ship the English interface and manual.
How do we obtain replacement blades and belts?
For blades, belts and other wear parts, every quote lists them with unit price and the location they ship from. We identify the replacement parts for your machine configuration.
Related machines in Tube, Tape & Material Cutting
Hot and Cold Webbing Shape Cutting Machine, 45–135°
Model WM-566
Automatic Braided Sleeve Taping and Cutting Machine for OD 8–30 mm Tube
Model WM-177
Automatic Cold-Knife Tube and Strip Cutting Machine, 100 mm Width
Model WM-611