🌐 English ▾

Selection guide

Crimping Machines and Applicators for Molex, JST and TE/AMP Reel Terminals

Choose a reel-terminal crimping press by terminal part number, feed direction, applicator fit and first-piece acceptance for Molex, JST and TE/AMP jobs.

Technical lead: Lao Xiaoyu (劳晓宇) · Senior Engineer
Content updated:

Choose a reel-terminal crimping machine from the exact terminal part number and the way your wire reaches the press. A semi-automatic bench press works when an operator presents prepared wires. An automatic cut, strip and crimp line can combine those operations when the cable, terminals and production mix fit the line. In both cases, specify the applicator for the terminal on its carrier.

Match the applicator to the terminal strip

What to identifyHow it affects your shortlist
Complete terminal part number and packagingUse the terminal drawing and tooling reference for the supplied part. A housing number helps identify the connector family, while the contact number is needed to match the tooling.
Carrier pitch and feed directionCompare the actual strip with the feed track and pawl. The space for the reel, guides and scrap depends on how the terminal enters the station.
Conductor size, construction and insulation ODCheck the application specification for both the conductor crimp and the insulation support. Two wires marked with the same AWG can have different insulation diameters.
Existing applicator and pressRecord base and ram geometry, shut height, stroke, feed actuation and guarding clearance. Use the press reuse checklist.

The Molex application tooling directory explains how to look up the tooling specification by part number. The JST crimp tooling guide lists tooling and connection requirements by terminal. The TE/AMP OCEAN tooling guide illustrates how end-feed and side-feed applicators present the terminal. These references establish what to check on each job.

Compare bench and automatic routes

Your production setupWiromac shortlistConfirm in the trial
Pre-stripped leads and mixed batchesWM-3102T semi-automatic press with interchangeable OTP and 2000# tooling families listedTool fit and feed direction for the exact strip, time to change over, and operator access for the shortest lead
Pre-stripped leads and a servo bench pressWM-3102S servo press with 20 kN rated force and a standard 30 mm strokeApplicator geometry, connection quality, and any monitoring required on the order
Wire from a spool and automatic crimping at one or both endsWM-3202 automatic line for AWG 28–18 wire, with a published cut length of 40–9,900 mmTerminal presentation at each station, minimum finished lead length, and accepted parts per hour

When the contacts arrive loose or have a solid barrel

Identify the package and the specified crimp profile before choosing the feed architecture. TE Connectivity’s DEUTSCH contact guide distinguishes stamped contacts from solid contacts and shows why their crimp forms differ. For a DEUTSCH or Mil-Spec contact, use its application documentation to identify the approved tool, positioner and indent profile. For selected loose closed-barrel terminals where a custom automatic process is permitted, our WM-3248 loose-terminal line is a candidate to evaluate with samples.

Approve the first pieces against the specified conductor crimp, insulation support, cut-off tab and terminal position. Agree on pull testing or cross-section inspection where required, then repeat the check after a tooling change. Ask us to quote a reel-terminal crimping setup. The terminal number and a photograph of the strip are enough to start.

See the process in action

Demonstrations from the machines referenced in this guide. Click to watch the operation, then request a trial with your own material.

Questions engineers ask

Which crimping machine should I shortlist for Molex, JST or TE/AMP terminals on reels?

For pre-stripped wires, compare a bench press such as WM-3102T or WM-3102S. To cut, strip and crimp wire from a spool, compare the WM-3202 within its published wire range. Confirm the applicator and feeding arrangement with the exact terminal and wire before ordering.

Can the same applicator run every terminal from one connector brand?

Use the exact terminal part number to find the specified tooling. Within a connector brand, carrier design, feed direction, barrel geometry, and the wire and insulation range can differ.

👋 Need help choosing a machine? Ask me about specifications, processes and sample trials.
Email
Wiro — Equipment Assistant Equipment guidance · quotation team replies within 12 h