🌐 English ▾

Heat Shrink Tube Cutting, Inserting and Shrinking Machine for Flat Cable WM-675

CE Certified HS Code 8419.89 Tube Φ7–16 mm 300–1,000 pcs/h
Get a quote for WM-675 →

The WM-675 takes heat shrink tube from Φ7 to 16 mm straight off the reel, cuts it to the programmed length, slips it over the cable end and bakes it sealed between two heating tubes — one above, one below — so the sleeve shrinks evenly all the way around flat sheathed cable. The operator loads and unloads; the machine does the rest, at 300 to 1,000 pieces per hour depending on hand speed. Tube length, upper and lower baking temperatures and piece counts are set on a color HMI touchscreen with an English interface, with parameter lockout and one-click restore to keep recipes from drifting.

Specifications

ModelWM-675
FunctionHeat shrink tube inserting and sealing on cable ends
Operation modeSemi-automatic — operator loads the cable, machine feeds, cuts, inserts and shrinks the tube
Heat shrink tube diameterΦ7 – 16 mm
Production capacity300 – 1,000 pcs/hour (depending on manual operation speed)
Heating methodDouble heating tubes, baking from above and below
Temperature controlDigital, independent upper and lower heater settings, with abnormal-state monitoring
DisplayColor HMI touchscreen, English interface
Air supplyCompressed air (onboard filter-regulator unit)
Electrical configurationFor any electrical equipment included in the order, we configure the supply for your installation. The quote confirms the voltage, phase, frequency, current and the power cord with plug or industrial connection for your site. Common site supplies are 120 V, 60 Hz with grounded Type B outlets in the US and Canada, with 208 V or 240 V also found at industrial sites. The UK and Ireland use 230 V, 50 Hz with Type G. Australia and New Zealand use nominal 230 V, 50 Hz with Type I, and some Australian sites list 240 V. Three-phase installations in the UK, Ireland, Australia and New Zealand commonly use 400 V at 50 Hz, with 415 V at some Australian sites.
Lead timeYour quote confirms the machine configuration, included accessories and dispatch date.
Warranty and supportOne-year machine warranty and free remote video support for the life of the equipment.
Wear partsFor wear parts, every quote lists them with unit price and the location they ship from.
HS Code8419.89 (common reference — final classification confirmed by your customs broker)
CertificationCE (certificate provided with shipment)

Key features

  • Two heating tubes bake the sleeve from above and below at the same time — an even, sealed shrink on flat sheathed cable, where single-side heat leaves the far side loose
  • Tube feeds from the reel stand and is cut to the length set on the screen, so every cable in the batch carries the same sleeve at the same spot
  • Compressed-air protection on the heating unit and abnormal-state monitoring on the temperature loop extend heater life and catch faults before they scrap parts
  • Parameter lockout stops operators from nudging a recipe off spec — and one click restores the stored settings if anything has been changed

What it processes

  • Shrink-sealing over crimped ring terminals on flat sheathed cable and battery jumper leads
  • Insulation and strain-relief sleeves, Φ7–16 mm, on sheathed cable ends for energy storage and power wiring
  • Repeatable sleeve length and position on high-voltage cable assemblies where every piece must match

Suited for: heat shrink tube inserting and sealing on flat sheathed cable ends — sleeve OD Φ7 to 16 mm cut from the reel, placed and shrink-sealed over crimped ring terminals and cable ends, one operator, 300–1,000 pieces per hour. For other jobs and machine options: small sleeves below Φ7 on thin hookup wire — for Φ2.0–Φ8.0 sleeves at up to 2,500 pcs/h, pick the WM-663 heat shrink tube inserting and heating machine; nor for shrinking mid-span splices or already-assembled harness bundles — that is work for the WM-664 infrared harness heat shrink oven, which takes harness sections up to Ø100 mm, or the wider heat shrink processing category.

Tube wall thickness and shrink ratio vary by brand, so we prove it before you pay: send 2–3 meters of your cable, your terminals and a length of your actual tube — we run them on this machine and send you the trial video first. For a WM-675 quote, share the sleeve size and the approximate dimensions of the part it covers. We’ll check which configuration fits your assembly.

Compare configurations before you order Tell us what you need to make. We’ll help you shortlist the equipment and identify which tooling and accessories to include in your quote. Help me choose a machine →

WM-675 — common questions

What does the WM-675 automate, and what stays manual?

The operator presents the cable end and takes the finished piece away — that is the manual part, and it is why rated output spans 300 to 1,000 pieces per hour. Everything between is automatic — the machine pulls tube from the reel, cuts the programmed length, positions it over the cable end and bakes it sealed between the upper and lower heating tubes.

Can it shrink-seal over a crimped ring terminal?

Yes — that is its typical job. The sleeve slides over the crimp barrel and shrinks down tight against the cable jacket, insulating and sealing the joint in one pass. Send us 2–3 meters of your cable with your terminals and tube — we run them on this machine and send you the video before you order.

Which tube sizes does it take, and what if mine are smaller?

It handles heat shrink tube from Φ7 to 16 mm outer diameter. For small sleeves from Φ2 to Φ8 on thin wire ends at higher throughput, the WM-663 inserting and heating machine is the better match — tell us your tube spec and we will point you to the right platform.

Related machines in Heat Shrink & Tube Insertion

👋 Need help choosing a machine? Ask me about specifications, processes and sample trials.
Email
Wiro — Equipment Assistant Equipment guidance · quotation team replies within 12 h