Shield Braid Brushing, Cutting and Fold-Back Machine for 3–9 mm Shielded Cable WM-181
The WM-181 prepares the braided shield on cable ends from 3.0 to 9.0 mm OD — rotating steel brushes open and comb the braid, the blade trims it to a set remaining length of 3 to 10 mm, and the machine folds it back over the jacket, ready for a 360° shield termination. It works on strip windows from 8 to 35 mm at 700–1,000 pieces per hour, uses a 220 V reference supply (600 W) and 0.4–0.6 MPa of air, and sits on a bench at 580 × 500 × 400 mm. Blades and brushes are the only consumables.
Specifications
| Model | WM-181 |
|---|---|
| Applicable cable diameter | OD 3.0 – 9.0 mm |
| Stripping length | 8 – 35 mm |
| Shield remaining length | 3 – 10 mm |
| Work efficiency | 700 – 1,000 pcs/h |
| Air pressure | 0.4 – 0.6 MPa |
| Power supply | Reference configuration: 220 V, 60 Hz, 600 W |
| Dimensions | 580 × 500 × 400 mm |
| Consumables | Cutting blades and brushes |
| Electrical configuration | We configure the machine’s electrical supply for your installation before shipment. Your quote confirms the voltage, phase, frequency, current and the power cord with plug or industrial connection for your site. Common site supplies are 120 V, 60 Hz with grounded Type B outlets in the US and Canada, with 208 V or 240 V also found at industrial sites. The UK and Ireland use 230 V, 50 Hz with Type G. Australia and New Zealand use nominal 230 V, 50 Hz with Type I, and some Australian sites list 240 V. Three-phase installations in the UK, Ireland, Australia and New Zealand commonly use 400 V at 50 Hz, with 415 V at some Australian sites. |
| Lead time | Your quote confirms the machine configuration, included accessories and dispatch date. |
| Warranty and support | One-year machine warranty and free remote video support for the life of the equipment. |
| Wear parts | For wear parts, every quote lists them with unit price and the location they ship from. |
| HS Code | 8463.90 (common reference — final classification confirmed by your customs broker) |
| Certification | CE (certificate provided with shipment) |
Key features
- Steel wire brushes open and comb the braid; we confirm brush settings and inspect the underlying insulation on your cable sample
- Trims the shield to a repeatable 3–10 mm remaining length and folds it back over the jacket in one clamp cycle
- One operator loads pre-stripped ends and takes out finished, fold-backed shields at 700–1,000 pieces per hour
- Blades and brushes are the only wear parts, listed as standard consumables and swapped without special tools
What it processes
- Shielded cable prepared for EMC glands, ferrules and 360° shield contacts
- Sensor, signal and camera harnesses with 3–9 mm OD shielded cable
- New-energy and industrial assemblies where hand-combed braid is too slow and too inconsistent
Suited for: shielded cable from 3.0 to 9.0 mm OD whose braid must be opened, trimmed to 3–10 mm and folded back over the jacket — the end state EMC glands and 360° shield ferrules expect. For other jobs and machine options: cutting to length, jacket stripping or foil-only shields — for the upstream cut and jacket work, pair it with the WM-184X rotary blade cut and strip machine, built for the same braided and shielded constructions; foil shields are a job for the coaxial cable processing machines.
Braid density and lay length vary between cable makes: send 2–3 meters of your actual shielded cable and we run it on this machine on video before you order. For a WM-181 quote, tell us the cable outside diameter and how the shield should look after processing. A photo of the end is enough to begin the fit check.
Engineering knowledge
Choose and troubleshoot this process
- Braid Brushing vs Wire Untwisting: Choose the Right Cable Preparation ProcessSeparate braid opening, shield cutting, fold-back and wire-pair untwisting. Choose equipment from the finished cable end and connector requirements.
WM-181 — common questions
What exactly does the WM-181 do to the braid?
In one cycle it brushes the exposed braid open, combs the strands straight, cuts them to a set remaining length between 3 and 10 mm, and folds the stub back over the jacket. The gallery shows the stages on real samples — combed, gathered and folded back.
What condition must the cable arrive in?
Cut to length with the outer jacket already removed over an 8–35 mm window, exposing the braid. Cable outer diameter must be between 3.0 and 9.0 mm; the reference build uses 220 V (600 W) and requires 0.4–0.6 MPa of compressed air. We confirm the electrical connection for your site.
Does it cut cable to length or strip the jacket itself?
No — shield work is its whole job. Do the cutting and jacket stripping upstream on one of the automatic cut and strip machines in this category, then feed the exposed braid ends to the WM-181.
Related machines in Shield Brushing & Processing
Shield Brushing Machine for Braided and Spiral-Served Cable, 50 mm Brushing Length
Model WM-821
EV Cable Stripping, Foil and Braid Cutting, and Shield Fold-Back Machine
Model WM-199
Electrode-Type Metal Braid Stripping Machine for Shielded and Thermocouple Wire
Model WM-166