Adjustable Hot Air Heat Shrink Station for Cable Ends and Splices WM-677
The WM-677 is a bench-top hot-air station for shrinking tube onto cable ends, splices and connector breakouts. A 3 kW resistance element heats the air, a 50 W centrifugal blower pushes it through an insulated duct into a stainless gun barrel, and that barrel is clamped to a height-adjustable post that rotates 360° — the operator brings the air to the joint instead of twisting the harness around a fixed outlet. Maximum outlet air temperature rise is above 395 °C with a 430 °C withstand ceiling, the heating wire is rated for 100,000 hours, and the double-insulated housing limits heat transfer to the outside; follow the operating instructions around hot surfaces. The whole unit draws 3,050 W from a single 220 V two-phase supply, weighs 10 kg, and measures 320 × 255 × 430 mm — 600 mm long once the heater arm is counted.
Specifications
| Model | WM-677 |
|---|---|
| Function | Hot-air heating and shrinking of heat shrink tube (bench station, gun head on an adjustable bracket) |
| Machine size | 320 × 255 × 430 mm without heater bracket; 600 × 255 × 430 mm including heater bracket |
| Air outlet size | 50 mm / 25 mm |
| Outlet adjustment | 360° rotation in all directions |
| Insulation layer | Double insulation |
| Heater | Resistance heating, 3 kW |
| Temperature control method | Intelligent temperature adjustment |
| Temperature control accuracy | ± 1 °C |
| Heating wire service life | 100,000 h |
| Blower | 50 W |
| Maximum air volume | 138 m³/h — actual air volume about 80 m³/h |
| Static pressure | 218 Pa |
| Maximum air outlet temperature rise | > 395 °C |
| Maximum withstand temperature | < 430 °C |
| Power supply | Reference configuration: 220 V, two-phase |
| Machine power | 3,050 W |
| Machine weight | 10 kg |
| Electrical configuration | We configure the machine’s electrical supply for your installation before shipment. Your quote confirms the voltage, phase, frequency, current and the power cord with plug or industrial connection for your site. Common site supplies are 120 V, 60 Hz with grounded Type B outlets in the US and Canada, with 208 V or 240 V also found at industrial sites. The UK and Ireland use 230 V, 50 Hz with Type G. Australia and New Zealand use nominal 230 V, 50 Hz with Type I, and some Australian sites list 240 V. Three-phase installations in the UK, Ireland, Australia and New Zealand commonly use 400 V at 50 Hz, with 415 V at some Australian sites. |
| Lead time | Your quote confirms the machine configuration, included accessories and dispatch date. |
| Warranty and support | One-year machine warranty and free remote video support for the life of the equipment. |
| Wear parts | For wear parts, every quote lists them with unit price and the location they ship from. |
| HS Code | 8419.89 (common reference — final classification confirmed by your customs broker) |
| Certification | CE (certificate provided with shipment) |
Key features
- The heater barrel is clamped to a height-adjustable post and turns 360° in every direction — awkward joints get met at the angle they already sit at, instead of the operator bending a stiff harness back towards a fixed air outlet
- Blower and heater live in separate boxes joined by an insulated flexible duct, so the hot end stays small and light at the work point while the fan noise and mass sit back on the base plate
- 3 kW of resistance heat behind a modest 50 W, 138 m³/h fan — enough energy to shrink tube quickly, but a gentle enough air stream that thin wires and loose leads are not blown out of the fixture
- Double-insulated stainless housing with a 100,000-hour rated heating wire and a 430 °C withstand ceiling, built to stay at temperature through a full shift rather than cycling like a trigger-held gun
- 10 kg total on a flat base plate with a carry handle, with a 220 V reference supply — no compressed air line, no gas bottle, and two hands are enough to move it to another bench
What it processes
- Shrinking sealing boots and strain-relief tube over high-voltage EV cable breakouts and connector backshells
- Seating transition and branch tube on multi-core control and instrumentation harnesses
- Shrinking dual-wall adhesive-lined tube over splices, lugs and battery cable ends at a repair or rework bench
- Shrinking printed identification sleeves onto panel and cabinet wiring
Suited for: operator-paced shrinking where the joint will not come to a fixed outlet — connector backshells, high-voltage cable breakouts, branch transitions and marker sleeves. The gun head swings to the work, the controller holds the heat, and 3 kW is enough for dual-wall adhesive-lined tube as well as thin-wall. For other jobs and machine options: rated volume production — this machine is paced by the operator’s hand, so for a throughput number on a moving belt take the WM-666 crawler belt tunnel oven at 2,000 pcs/h instead. For other jobs and machine options: heavy cable ends and large-diameter shrink caps that need heat from both sides at once — the WM-668F twin-nozzle hot air machine delivers 4 kW through two opposed Ø50 mm nozzles with freely adjustable nozzle spacing. For other jobs and machine options: cutting and inserting the tube before it is shrunk — this station only heats. If the tube also has to be fed, cut and slid onto the wire, the WM-663 inserting and heating machine does all three at 800 – 2,500 pcs/h.
Send us a length of your harness with the exact shrink tube you use. We run it on this station and post the shrunk samples back, so the seating, the gloss and the edge of the tube are judged on your own parts before any order is placed.
The listed heating-wire life is 100,000 h; it is a component rating, not a warranty for that duration. Confirm the duty conditions, electrical connection and replacement schedule on the quote. For a WM-677 quote, share the sleeve size and the approximate dimensions of the part it covers. We’ll check which configuration fits your assembly.
Engineering knowledge
Choose and troubleshoot this process
- Heat Shrink Defects: Causes and Corrective ActionsTroubleshoot incomplete recovery, wrinkles, splits, scorching, sleeve movement, trapped air, uneven adhesive flow and heat damage.
- How to Choose Heat Shrink Processing EquipmentChoose heat shrink equipment by sleeve material, recovered dimensions, adhesive requirement, harness geometry, heating method, takt time and validation plan.
WM-677 — common questions
Is this a handheld heat gun?
The heater is a bench-mounted gun barrel clamped to a post on the machine's own base plate, fed by a separate blower box through an insulated duct. The operator's hands stay on the wire, not on a trigger — which is why it can hold temperature continuously through a shift instead of heating and cooling on every pull.
Which air outlet does it come with?
The datasheet lists outlet sizes of 50 mm and 25 mm. The unit in our photographs is fitted with a U-shaped saddle outlet that straddles the wire and blows onto it from both flanks — useful when tube has to seat evenly all the way round a breakout. Tell us the joint geometry and tube sizes you shrink most and we will confirm which outlet ships with your machine before you order.
What tube and harness diameters does it handle?
Harness diameter compatibility and hourly output are confirmed on the quote after a trial. The specification lists 3 kW of heat, an outlet air temperature rise above 395 °C, and maximum airflow of 138 m³/h, with actual airflow about 80 m³/h. Send your tube and cable; we shrink samples on this machine and return them for finish inspection.
When should I consider another machine?
Volume production and very large sections. It is an operator-paced station — one joint at a time, presented by hand. For a rated throughput on a conveyor, see the WM-666 crawler belt tunnel oven at 2,000 pcs/h. For thick cable ends and large-diameter shrink caps, the WM-668F twin-nozzle machine puts 4 kW through two opposed Ø50 mm nozzles.
Related machines in Heat Shrink & Tube Insertion
Aluminum-Frame Bench Heat Shrink Conveyor Oven, 800 × 400 × 150 mm
Model WM-690
Aluminum-Frame Heat Shrink Conveyor Oven, 1200 × 400 × 150 mm
Model WM-698
Aluminum-Frame Heat Shrink Conveyor Oven with 360 mm Heating Width
Model WM-694